my dev.board - Waveshare ESP32-S3-Zero

ESP32-S3-Zero by Waveshare

Product page:
~ ESP32-S3-Zero - Waveshare Wiki



Pinout:



Close-up view:


Arduino Exercise:
~ BlinkRGB Exercise run on WaveShare ESP32-S3-Zero, in Arduino Framework
~ ESP32-S3-Zero display on 0.85 inch 128x128 LCD with GC9107 SPI driver, using Arduino_GFX.
~ Fix ESP32-S3-Zero Serial.print() not work - enable USB CDC on Boot

CircuitPython:
~ Install esptool inside Virtual Environment, on Raspberry Pi 5 running 64-bit Raspberry Pi OS (bookworm).
~ Install CircuitPython firmware on Waveshare ESP32-S3-Zero
~ CircuitPython I2C Scanner, run on ESP32-S3-Zero
~ ESP32-S3-Zero/CircuitPython Display on 128x64 SSD1306 I2C OLED
~ ESP32-S3-Zero/CircuitPython read single key using keypad.Keys and control onboard RGB LED (NeoPixel)
~ Use VL53L0X (Time of Flight distance sensor) on ESP32-S3/CircuitPython
~ 3-wire 9-bit SPI ST7789 TFT with FT6236 capacitive touch on ESP32-S3-Zero/CircuitPython
~ CircuitPython exercise to control servo motor, run on ESP32-S3-Zero/CircuitPython 9.0.0-beta.0.
~ Radar-like distance scanner on ESP32-S3/CircuitPython 9, using SG90 servo motor, VL53L0X distance sensor and SSD1306 OLED.
~ ESP-NOW on CircuitPython 9.0.3, tested on ESP32-S3/ESP32-C3.
~ CircuitPython ESP-NOW: Remote control on-board RGB LED via wireless, between ESP32-S3.

Comments

Post a Comment

Popular posts from this blog

480x320 TFT/ILI9488 SPI wih EP32C3 (arduino-esp32) using Arduino_GFX Library

Image
Display on 3.5 inch 480x320 TFT with SPI ILI9488 (SKU:MSP3520) with XIAO EP32C3 (arduino-esp32) using Arduino_GFX Library. Install GFX Library for Arduino (Arduino_GFX) in Library Manager. Arduino_GFX is a Arduino graphics library supporting various displays with various data bus interfaces. This library start rewrite from Adafruit_GFX, LovyanGFX, TFT_eSPI, Ucglib, and more... Connection:      Connection between XIAO ESP32C3 and      3.5" 480x320 TFT with SPI ILI9488 (SKU:MSP3520)      XIAO ESP32C3                        +-------------+           +---------|GPIO2    5V      |          | +-----|GPIO3    GND    |-----------+ | +-|-----|GPIO4    3V3    |---------+ | | | | +---|GPIO5    GPIO10|-------+ | | | | | |    |GPIO6    GPIO9 |         | | | | | | | |GPIO7    GPIO8 |-----+ | | |           | | | |    |GPIO21   GPIO20 |    | | | | | | | | +-------------+      | | | | ILI9488 SPI TFT | | | |         | | | | +--------
Read more

my dev.tools - FNIRSI 2C23T 3-in-1 Dual Channel Oscilloscope/Multimeter/Signal Generator

Image
FNIRSI 2C23T 3-in-1 Dual Channel Oscilloscope/Multimeter/Signal Generator Steps to upgrade of FNIRSI 2C23T 3-in-1 : Remark@2024-03-23: Please check the comment by dmitriivanov5330 in the video. How to distinguish the hardware? please press menu , and if you can see the words in Setting: "Hardware version No.:XXXXX " then the device is made with latest hardware, it has the latest firmware, and now it doesn't need to upgrade.  If you can not see the words in Setting: "Hardware version No.:XXXXX ", then it is made with old hardware, and it can be upgraded with firmware 2.0.2, and if you confirm this, the firmware for the device with old hardware is attached.  By the way, the firmware 2.0.2 only fixes device with old hardware. The device with new hardware can not use this firmware to upgrade. - Download firmware from FNIRSI Official Web Site - Connect USB to PC - While 2C23T is OFF, press and hold MENU button, then press POWER button to power
Read more